Fevicol SH- 20kg
Fevicol SH has 60 years of trust and durability which is unmatched by any other adhesive in the country. It is an excellent adhesive for pasting wood, laminate, MDF, Particleboard. It is easy to apply and use.
TECHNICAL DATA OF FEVICOL SH ADHESIVE-
FEVICOL SH is synthetic resin based adhesive in the form of a Milky White viscous paste, and is ready to use for all wood working applications. It is non – flammable and non-toxic in nature.
TYPICAL PROPERTIES-
- Appearance :Milky white emulsion
- Viscosity at 30 °C, Poise :200 to 300 ( By B.F. RVT Spl.-6, RPM – 20. )
- pH :4.0 to 6.0
- Specific Gravity :1.05 to 1.09
- Flow :Continuous
- Spreadability : Smooth and easy
FIELD OF APPLICATION
Furniture Industries- Bonding laminate, plywood, veneer, particleboard, MDF, block board, hard board to each other.
Non-furniture Industries- Bus body building where wood is used
APPLICATION METHOD
- Surfaces to be bonded should be free from oil; grease; dust and dirt and should be dry and properly levelled.
- For best results, roughen the surfaces to be bonded.
- Stir content of container before use.
- Apply even coats of FEVICOL SH first on comparatively non-porous surface, and then on porous surface for e.g. apply first on laminate and then on plywood.
- If possible, application should be lengthwise on one surface and breadth-wise on other surface. This will help in proper and uniform spreading of adhesive while pressing.
- Before allowing adhesive to dry, bring both the surfaces in contact, make proper alignment, and start pressing from one side by using wet squeezed cloth to avoid bubbles, and ensuring uniform contact.
- Pressure can be given by using nails; clamps; weight; masking tape etc.
- Excess adhesive; which oozes out from edges should be wiped off with wet squeezed cloth.
- To get best results, bonded surfaces are to be kept under pressure for 24 hrs.
- If required, pressure can be released after 4-6 hrs and the bonded assembly can be put to use. In case of highly porous surfaces like particleboard and MDF, it is advised that, a thin coat of FEVICOL SH is applied by pressure on the surface and allowed to dry. This will fill the pores of the surface. After drying, light sanding is to be done for getting smooth leveled surface and then this surface is bonded as per the method shown above.
PRODUCT COMPLIANCE
Low VOC value meets for the Certification of LEED / Green, Free Formaldehyde Certification, ROHS Compliance
COVERAGE- Approx.32 – 36 sq.ft/kg
ADVANTAGES
- Solvent free, Non-hazardous, Non-flammable, No fire hazards.
- Free from offensive smell.
- If required it can be diluted with clean water till applicability is achieved.
- Very quick setting time. Handling strength is achieved within 6-8 hrs of application.
- Superior flow and spreadability and hence it can give higher coverage.
- Excellent bond strength offering better moisture resistance.
- Heat resistance in normal case
- Can be applied by brush, roller, spreader, fingertip OR any suitable applicator.
- Easy to clean up while wet.
- Excellent film formation.
- Dries clear.
PRODUCT GUIDELINES
PRECAUTIONS- When not in use, container should be kept closed. Skin formation if any, should be removed from the surface before use.
SHELF LIFE- Best to use before 24 months from the date of manufacturing.
STORAGE- Store in cool & dark shaded place; away from the sunlight.
NOTE : We recommend that before using our product, the customer should make his own test to determine the suitability of the product for his own purpose under his operating conditions. As the circumstances under which our product is stored, handled and used, are beyond our control, we cannot assume any responsibility for their use by the customer
Our latest content
Check out what's new in our company !